Saltar navegación principal
Normas DIN – AENOR
DIN ISO 10816-3:2018-01

DIN ISO 10816-3:2018-01

Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts - Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15000 r/min when measured in situ (ISO 10816-3:2009 + Amd.1:2017)

Vibrations mécaniques - Évaluation des vibrations des machines par mesurages sur les parties non tournantes - Partie 3: Machines industrielles de puissance nominale supérieure à 15 kW et de vitesse nominale de fonctionnement entre 120 r/min et 15000 r/min, lorsqu'elles sont mesurées in situ (ISO 10816-3:2009 + Amd.1:2017)

Mechanische Schwingungen - Bewertung der Schwingungen von Maschinen durch Messungen an nicht-rotierenden Teilen - Teil 3: Industrielle Maschinen mit einer Nennleistung über 15 kW und Nenndrehzahlen zwischen 120 min<(hoch)-1> und 15000 min<(hoch)-1> bei Messungen am Aufstellungsort (ISO 10816-3:2009 + Amd.1:2017)

Fecha:
2018-01 /Active
Equivalencias internacionales:

ISO 10816-3 AMD 1 (2017-08)

ISO 10816-3 (2009-02)

Relación con otras normas DIN:
Resumen:
The standard provides specific guidance for assessing the severity of radial vibration measured on the bearing housings of industrial machines in situ. The criteria provided in this document apply to machine sets having a power above 15 kW and operating speeds between 120 r/min and 15000 r/min. The machine sets covered by this part of ISO 10816 include: - steam turbines and generators with outputs less than or equal to 40 MW; - steam turbines and generators with outputs greater than 40 MW and speeds other than 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (although generators seldom fall into this category); - rotary compressors; - industrial gas turbines with outputs less than or equal to 3 MW; - electrical motors of any type; - blowers or fans. Two criteria are provided for assessing the machine vibration when operating under steady state conditions. One criterion considers the magnitude of the observed vibration; the second considers changes in the magnitude. In addition, different criteria are provided for transient operating conditions, such as run-up and coast-down. The evaluation procedures presented in this part of ISO 10816 are based on broad-band measurements. The following are excluded from this part of ISO 10816: - steam turbines and/or generators with outputs greater than 40 MW and speeds of 1500 r/min, 1800 r/min, 3000 r/min or 3600 r/min (see ISO 20816-2); - gas turbine sets with outputs greater than 3 MW (see ISO 10816-4 and ISO 20816-2); - machine sets in hydraulic power generating and pumping plants (see ISO 10816 5); - machines coupled to reciprocating machines (see ISO 10816 6); - rotodynamic pumps including integrated electric motors, i.e. where the impeller is mounted directly on the motor shaft or is rigidly attached to it (see ISO 10816 7); - rotary positive displacement compressors (e. g. screw compressors); - reciprocating compressors (see ISO 10816-8); - reciprocating pumps; - submerged motor-pumps; - wind turbines.
Keywords:
Acceptance tests, Bearing housings, Bearings, Classification, Components, Compressors, Electric motors, Enclosures, Evaluations, Gas turbines, Generators, In situ, Industrial turbine, Installation locations, Instructions, Machine vibration, Machines, Measurement, Measuring techniques, Mechanical testing, Performance, Power ratings, Rotary compressor, Rotational speeds, Stationary, Steam turbines, Turbocompressors, Vibration, Vibration engineering, Vibration measurement, Vibration severity, Vibration tests
65,98
Idioma Formato

Formato digital

Nota: Precios sin IVA ni gastos de envío

Añadir a la cesta