Saltar navegación principal
Normas ASTM – AENOR
ASTM D3754-19

ASTM D3754-19

Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe

Fecha:
2019-12-16 /Active
Abstract:

This specification covers machine-made fiberglass pipe for use in pressure systems for conveying sanitary sewage, storm water, and many industrial wastes, and corrosive fluids. Both glass-fiberreinforced thermosetting-resin pipe (RTRP) and glass-fiberreinforced polymer mortar pipe (RPMP) are fiberglass pipes. This standard is suited primarily for pipes to be installed in buried applications, although it may be used to the extent applicable for other installations such as, but not limited to, jacking, tunnel lining and slip-lining and rehabilitation of existing pipelines. The pipe is intended to operate at certain internal gage pressures. The fiberglass sewer and industrial pressure pipe are defined by raw materials in the structural wall (type) and liner, surface layer material (grade), operating pressure (class), and pipe stiffness. Different tests shall be performed in order to determine the following properties of pipe: inside diameter, outside diameter, length, wall thickness, squareness of pipe ends, chemical resistance, soundness, stiffness, hoop-tensile strength, beam strength, longitudinal tensile strength, and longitudinal compressive strength.

Scope:

1.1 This specification covers machine-made fiberglass pipe, 8 in. (200 mm) through 156 in. (4000 mm), for use in pressure systems for conveying sanitary sewage, storm water, and many industrial wastes, and corrosive fluids. Both glass-fiber-reinforced thermosetting-resin pipe (RTRP) and glass-fiber-reinforced polymer mortar pipe (RPMP) are fiberglass pipes. This standard is suited primarily for pipes to be installed in buried applications, although it may be used to the extent applicable for other installations such as, but not limited to, jacking, tunnel lining and slip-lining and rehabilitation of existing pipelines. Pipe covered by this specification is intended to operate at internal gage pressures of 450 psi (3103 kPa) or less.

Note 1: For the purposes of this standard, polymer does not include natural polymers.

1.2 The values given in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

3

Grade  

1
Polyester resin surface layer—
reinforcedB

2
polyesterB resin surface layer—
nonreinforcedB

3
polyesterB resin and sand surface layer nonreinforced

4
epoxy resin surface layer—
reinforced

5
epoxy resin surface layer—
nonreinforced

6
No surface layer

4

  ClassC

C50

C100

C150

C200

C250

C300

C350

C400

C450

5

Pipe Stiffness
 psi (kPa)

A
9 (62)

B
18 (124)

C
36 (248)

D
72 (496)ABC

1.3 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 2: There is no known ISO equivalent to this standard.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords:
fiberglass pipe; sewer pipe; industrial pipe; pressure pipe; strain corrosion; hydrostatic design basis;
47,8
Idioma Formato

Formato físico y digital

Nota: Precios sin IVA ni gastos de envío

Añadir a la cesta