ASTM Standard | Designation |
Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter | D2239 |
Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe | D2609 |
Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing | D2683 |
Standard Specification for Polyethylene (PE) Plastic Tubing | D2737 |
Standard Practice for Underground Installation of Thermoplastic Pressure Piping | D2774 |
Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing | D3261 |
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter | D3035 |
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter | F714 |
Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing | F1055 |
Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings | F1056 |
Standard Practice for Electrofusion Joining Polyolefin Pipe and Fittings | F1290 |
Standard Specification for Deformed Polyethylene (PE) Liner | F1533 |
Standard Guide for Construction Procedures for Buried Plastic Pipe | F1668 |
Standard Practice for Field Leak Testing of Polyethylene (PE) and Crosslinked Polyethylene (PEX) Pressure Piping Systems Using Hydrostatic Pressure | F2164 |
Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE) | F2206 |
Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings | F2620 |
Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method | F2634 |
Standard Practice for Field Leak Testing of Polyethylene (PE) Pressure Piping Systems Using Gaseous Testing Media Under Pressure (Pneumatic Leak Testing) | F2786 |
Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes ¾ in. to 65 in. | F2880 |
Standard Practice for Specimens and Testing Conditions for Testing Polyethylene (PE) Pipe Butt Fusions Using Tensile and Hydrostatic Test Methods | F2928 |
Standard Specification for Billets made by Winding Molten Extruded Stress-Rated High Density Polyethylene (HDPE) | F3034 |
Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) | F3123 |
Standard Practice for Data Recording the Procedure used to Produce Heat Butt Fusion Joints in Plastic Piping Systems or Fittings | F3124 |
Standard Practice for Guided Side Bend Evaluation of Polyethylene Pipe Butt Fusion Joint | F3183 |
Standard Practice for Heat Fusion Equipment (HFE) Operator Qualification on Polyethylene (PE) and Polyamide (PA) Pipe and Fittings | F3190 |
AWWA Standards | |
Standards Polyethylene (PE) Pressure Pipe and Tubing, 1/2 in. (13 mm) Through 3 in. (76 mm), for Water Service | C901 |
Polyethylene (PE) Pressure Pipe and Fittings, 4 In. Through 65 In. (100 mm Through 1,650 mm), for Waterworks | C906 |
CSA Standards | |
Standards Definitions, general requirements, and methods of testing for thermoplastic pressure piping | B137.0 |
Polyethylene (PE) pipe, tubing, and fittings for cold water pressure services | B137.1 |