ASTM D8047-17

Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine

Información:

Fecha:

2017-10-13 /Historical

Superseeded by:

D8047-19

Significance and Use:

5.1 Background—Prior to this test method, the ability of an engine lubricant to resist aeration was measured by the engine-oil aeration test (EOAT) described in Test Method D6894. The continued availability of engine parts coupled with field service aeration problems led to concerns about the relevance of this test method to newer oil and engine technologies. These concerns prompted the development of this new engine-oil aeration test method, based on the Caterpillar C13 engine and termed COAT. This test method aims to provide a more reliable measurement of the ability of a lubricant to resist aeration during engine operation in field service. The engine used is of current technology and the aeration measurement is operator independent.

5.2 Test Method—This test method evaluates aeration performance under high-engine-speed, zero-load operation in a turbocharged, heavy-duty, four-stroke diesel engine.

5.3 Use:

5.3.1 The tendency of engine oils to aerate in direct-injection, turbocharged diesel engines is influenced by a variety of factors, including engine oil formulation, oil temperature, sump design and capacity, residence time of the oil in the sump, and the design of the pressurized oil systems. In some engine-oil-activated systems, the residence time of the oil in the sump is insufficient to allow dissipation of aeration from the oil. As a consequence, aerated oil can be circulated to hydraulically activated components, adversely affecting the engine timing characteristics and engine operation.

5.3.2 The results from this test method may be compared against specification requirements such as Specification D4485 to ascertain acceptance.

5.3.3 The design of the test engine used in this test method is representative of many, but not all, diesel engines. This factor, along with the unique operating conditions, needs to be considered when comparing the test results against specification requirements.

Scope:

1.1 This test method evaluates an engine oil's resistance to aeration in automotive diesel engine service. It is commonly referred to as the Caterpillar-C13 Engine-Oil Aeration Test (COAT). The test is conducted under high-engine-speed (1800 r/min), zero-load conditions using a specified Caterpillar 320 kW, direct-injection, turbocharged, after-cooled, six-cylinder diesel engine designed for heavy-duty, on-highway truck use. This test method was developed as a replacement for Test Method D6894.

Note 1: Companion test methods used to evaluate engine oil performance for specification requirements are discussed in the latest revision of Specification D4485.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1 Exception—Where there is no direct SI equivalent, for example, screw threads, national pipe threads/diameters, and tubing size.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A2 for general safety precautions.

1.4 This test method is arranged as follows:

	Section
Scope	1
Referenced Documents	2
Terminology	3
Summary of Test Method	4
Significance and Use	5
Apparatus	6
Engine Liquids and Cleaning Solvent	7
Preparation of Apparatus	8
Engine Stand Calibration and Non-Reference-Oil Tests	9
Procedure	10
Calculation, Test Validity and Test Results	11
Report	12
Precision and Bias	13
Keywords	14
ASTM Test Monitoring Center Organization	Annex A1
Safety Precautions	Annex A2
Engine and Engine Build Parts Kit	Annex A3
Oil Temperature Control System	Annex A4
Engine Modifications and Instrumentation	Annex A5
External Oil System	Annex A6
Aeration Measurement System	Annex A7
Specified Units and Formats	Annex A8
ASTM TMC: Calibration Procedures	Annex A9
ASTM TMC: Maintenance Activities	Annex A10
ASTM TMC: Related Information	Annex A11
Engine Break-in and Silicon Passivation Procedure	Annex A12
Schedule for Taking Oil Samples and Carrying out Analyses	Annex A13
Determination of Operational Validity	Annex A14
Specification for PC-10 ULSD Fuel	Annex A15
Typical System Configuration	Appendix X1

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords:

automotive; Caterpillar C13; COAT; diesel engine oil; heavy-duty diesel engine; lubricants; oil aeration;

80,01 €

Formato físico y digital

Nota: Precios sin IVA ni gastos de envío

Añadir a la cesta