Saltar navegación principal
Normas ASTM – AENOR
ASTM A74-15

ASTM A74-15

Standard Specification for Cast Iron Soil Pipe and Fittings

Fecha:
2016-02-10 /Historical
Superseeded by:
Abstract:

This specification covers cast gray iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. These pipe and fittings are not intended for pressure applications. The cast iron shall be produced by an established commercial method that provides control over chemical and physical properties. Castings shall be sound, true to pattern, and of compact close grain that permits drilling and cutting by ordinary methods and its interior surface shall be reasonably smooth and free from defects. Ferrous scrap, pig iron, and any recycled ferrous material to be used in the melting operation shall be screened for radioactivity. Tension test shall include breaking load, machined diameter, and tensile strength. Chemical test shall conform to the chemical composition requirements prescribed for phosphorous, sulfur, chromium, titanium, aluminum, lead, and carbon equivalent. Dimension requirements for hub, spigot, barrel, grooves, water seal and trap, and threads of the pipe and fittings are detailed. The pipe and fittings shall be uniformly coated with a material suitable for the purpose.

Scope:

1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow plumbing, drain, waste and vent sanitary, and storm water applications. It establishes standards covering material, manufacture, mechanical and chemical properties, coating, test methods, inspection, certification, product markings, dimensions, and dimensional tolerances for extra heavy and service cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.

1.2 This specification covers pipe and fittings of the following patterns and, when so designated, shall apply to any other patterns that conform with the applicable requirements given in this specification.

1.2.1 Pipe:

 

Tables

Extra heavy, 21/2 ft (0.75 m), 31/2 ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m) lengths

1, 2

Service, 21/2 ft (0.75 m), 31/2 ft (1.0 m), 5 ft (1.5 m), 10 ft (3.0 m)

1, 2

Outside dimensions (for detailing)

X1.1

1.2.2 Fittings:

 

Tables

1/4 bends; long 1/4 bends

3, 4

1/4 bends, long low-hub

5

1/4 bends, low heel; high heel

6, 7

1/4 bends, short sweep; long sweep

8

1/4 bends, reducing long sweep

9

1/5 bends

10

1/6 bends

10

1/8 bends; long 1/8 bends

11

1/16 bends

11

Y branches

12, 13

Y branches, combination 1/8 bends, single

14

Y branches, combination 1/8 bends, double

14

Sanitary T branches, single

15

Sanitary T branches, double

15

Sanitary T branches, cleanout

16

Tapped sanitary T branches, single

17

Tapped sanitary T branches, double

17

T branches, single and double

18

Tapped T branches, single

19

Tapped T branches, double

19

T branches, cleanout

20

-45° offset fitting

21

Double hubs

22

Long double hubs

22

Reducers

23

Increasers

24, 25

P traps

26, 27

Deep seal P traps

28

Running traps

29

Screw plugs (brass)

30

Blind plugs

31

Iron-body ferrules

32

Side inlets

Fig. 3

Closet bends

33

Tapping bosses

34

Reducing 1/4 bend SV

35

Combination Y and 1/8 bend

36

‘H’ branch fitting

37

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

Keywords:
cast iron; fitting; hub and spigot pipe; pipe; soil pipe;
81,04
Idioma Formato

Formato físico y digital

Nota: Precios sin IVA ni gastos de envío

Añadir a la cesta