Saltar navegación principal
Normas ASTM – AENOR
ASTM D1282-05(2009)

ASTM D1282-05(2009)

Standard Test Method for Resistance to Airflow as an Indication of Average Fiber Diameter of Wool Top, Card Sliver, and Scoured Wool (Withdrawn 2018)

Fecha:
2018-01-19 /Historical
Superseeded by:
Significance and Use:

This test method is not recommended for the acceptance testing of commercial shipments of wool top, card sliver, or scoured wool since the referee method, Test Method D 2130, is recommended for that purpose. Although this test method is not recommended for acceptance testing, it is useful for fast quality control checks.

.If there are differences of practical significance between reported test results for two laboratories (or more), comparative test should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use the samples for such a comparative test that are as homogenous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, a probability level chosen prior to the testing series. If bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.

The specific area of the wool fibers is measured by the resistance in air flow. The resistance to air flow has been related to average fiber diameter measured by the microprojection method. The instruments have been calibrated to read average diameter in micrometres. Although the reading is affected by the average fiber diameter distribution of the specimen, the results secured by the instruments give no indication of this distribution. However, in converting the micrometres reading to millitex units (Annex A1), low, medium, and high standard deviations were used in the calculations to arrive at the range of millitex units which accordingly reflect the distribution of fiber diameters.


1) Balance Adjustment Knob 8) Porosity Calibration Control
2) Balance Pan 9) Compression Lever
3) Air Reservoir10) Calibrator Plug Plunger
4) Meter Zero Adjustment Screw11) Porosity Calibrator Plug
5) Porosity Test Chamber Lid12) Calibration Weight
6) Differential Pressure Gage13) Weighing Balance Mechanism
7) Porosity Zero Control14) Atomizer Bulb

FIG. 1 Port-Ar Apparatus


1) Metal specimen container 6) Gage tube
2) Packing rod 7) Millimetre scale
3) Plunger 8) Vacuum supply
4) Retaining collar 9) Upper gage tube mark
5) Control knob10) Lower gage tube mark

FIG. 2 WIRA Fiber Fineness Meter

Scope:

1.1 This test method covers the estimation of the average fiber diameter of wool fibers by use of the Port-Ar and the WIRA Fiber Fineness Meter instrument, which operate on the air-flow principle. Other air-flow instruments have not been tested with this method. The method is directly applicable to non-medullated, carded wool and wool top.

1.2 This test method is applicable to grease wool and scoured wool after the samples of such materials have been prepared as directed in Test Method D 2130.

Note 1—The use of the Micronaire instrument for measuring the fineness of cotton fibers is covered in Test Method D 1448.
The assignment of grade for wool and mohair is covered in Specifications D 3991 and D 3992.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords:
air-flow; diameter; wool; Airflow resistance; Diameter--textile fabrics/fibers; Micronaire reading; Port-Ar readings; WIRA fiber fineness instrument; Wool and wool top--fiber diameter
50,42
Idioma Formato

Formato físico y digital

Nota: Precios sin IVA ni gastos de envío

Añadir a la cesta