ASTM A800/A800M-20

Standard Practice for Estimating Ferrite Content of Stainless Steel Castings Containing Both Ferrite and Austenite

Fecha:

2020-05-13 /Active

Significance and Use:

4.1 The tensile and impact properties, the weldability, and the corrosion resistance of iron-chromium-nickel alloy castings may be influenced beneficially or detrimentally by the ratio of the amount of ferrite to the amount of austenite in the microstructure. The ferrite content may be limited by purchase order requirements or by the design construction codes governing the equipment in which the castings will be used. The quantity of ferrite in the structure is fundamentally a function of the chemical composition of the alloy and its thermal history. Because of segregation, the chemical composition, and therefore the ferrite content, may differ from point to point on a casting. Determination of the ferrite content by any of the procedures described in the following practice is subject to varying degrees of imprecision which must be recognized in setting realistic limits on the range of ferrite content specified. Sources of error include the following:

4.1.1 In Determinations from Chemical Composition—Deviations from the actual quantity of each element present in an alloy because of chemical analysis variance, although possibly minor in each case, can result in substantial difference in the ratio of total ferrite-promoting to total austenite-promoting elements. Therefore, the precision of the ferrite content estimated from chemical composition depends on the accuracy of the chemical analysis procedure.

4.1.2 In Determinations from Magnetic Response—Phases other than ferrite and austenite may be formed at certain temperatures and persist at room temperature. These may so alter the magnetic response of the alloy that the indicated ferrite content is quite different from that of the same chemical composition that has undergone different thermal treatment. Also, because the magnets or probes of the various measuring instruments are small, different degrees of surface roughness or surface curvature will vary the magnetic linkage with the material being measured.

4.1.3 In Determinations from Metallographic Examination—Metallographic point count estimates of ferrite percentage may vary with the etching technique used for identification of the ferrite phase and with the number of grid points chosen for the examination, as explained in Test Method E562.

4.2 The estimation of ferrite percent by chemical composition offers the most useful and most common method of ferrite control during melting of the metal.

4.3 For most accurate estimate of ferrite percent, a quantitative metallographic method should be used.

Scope:

1.1 This practice covers procedures and definitions for estimating ferrite content in stainless steel alloys containing both austenite and ferrite phases in amounts controlled to be within specified limits. Methods are described for estimating ferrite content by chemical, magnetic, and metallographic means.

Note 1: This practice can be used for cast austenitic and duplex stainless steel alloys (for example, CF-3, CF-3A, CF-8, CF-8A, CF-3M, CF-3MA, CF-8M, CF-8C, CG-8M, CH-10, CD4MCuN (1B), CD3MCuN (1C), CE8MN (2A), CD6MN (3A), CD3MN (4A), CE3MN (5A), CD3MWCuN (6A), and CD3MWN (7A)).

1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the practice.

1.2.1 Within the text, the SI units are shown in brackets.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Keywords:

austenite; austenitic stainless steel; ferrite; Schoefer<refdocr rid="r00001"/> Diagram; steel castings;

42,54 €

Formato físico y digital

Nota: Precios sin IVA ni gastos de envío

Añadir a la cesta